Blind Spot Mirrors

79Ghz lp67 Millimeter Wave Radar Blind Spot Detection System Warning System. 79Ghz Millimeter Wave Radar Moto Blind Spot Detection Auxiliary. The product consists of a 79Ghz millimeter wave radar, two warning lights and connecting wiring harnesses. This system product provides early warning of dangerous targets on the left and right rear of the motorcycle. 79Ghz millimeter wave radar has the unique ability to penetrate smoke, fog and dust, and is not affected by the weather. It can realize all-day applications, real-time detection of objects in the signal area, and identification of objects close to relative displacement. It can detect targets up to 50 meters away, and finally output an early warning signal. The early warning signal includes the warning light is always on and the warning light is flashing. Horizontal signal angle: ±75°. Antenna: dual-transmit and four-receive. Early warning range: horizontal -5 +5 meters, vertical 0 50 meters. Early warning speed range: 0KM/H120KM/H. Distance resolution: 0.4m. Ranging accuracy: better than 0.18m. Installation method: vertical installation at the rear. Power cord connection method. Connect the red wire of the power cord to the motorcycle’s ACC power supply (normal power when the car is started/out of power), and connect the black wire of the power cord to the negative pole of the motorcycle or ground. Radar wire connection method: the radar wire plug and the power cord plug are inserted into each other. The warning light plug corresponds to the warning light plug on the power cord, distinguishing the left and right, and fixing the warning light to a conspicuous driving posture near the instrument. 1 Radar installation height: 0.5. 1.2m from the ground. 2 Radar installation angle: The radar is fixed vertically to the ground. 3 Radar installation position: The radar is installed at the rear of the motorcycle, the radar signal surface corresponds to the rear of the motorcycle, the heat sink is on the top, and the cable outlet is on the bottom. Before making the actual lane change, be sure to visually inspect the surrounding area. This system is only used to assist you in detecting vehicles behind you when you change lanes. Due to certain restrictions in the actual working environment, this system cannot be completely relied on. If an accident occurs, our company will not be responsible. In the following situations, the radar may not make a warning. The vehicle is located behind the adjacent lane and maintains a relatively same speed for a long time. The adjacent lane where the vehicle is located is extremely wide, which exceeds the radar signal calculation range. When crossing a hill or the apex of a mountain road. The vehicle behind the ring road is out of signal range. 79Ghz millimeter wave radar1. Early warning warning light2. Due to the different display and lighting effects, the actual color of the item may be slightly different from the color displayed on the picture. Immediately you paid for the order. Communication always is best way to solve problem. We accept any return in 30 days that we promise. If item is defect or wrong when it. Please never return the parcel without agreement. From us, it is no possible for us to get the parcel. We at strive to give all of our customers a 5 star service. As this helps us maintain a quality service. Communication is very important, we believe we can resolve all the problem with you. It’s our pleasure to answer any questions you have. (weekend and holidays excluded). This item is in the category “Vehicle Parts & Accessories\Car Parts & Accessories\Exterior Parts & Accessories\Side View Mirrors\Mirror Assemblies”. The seller is “biety0315″ and is located in this country: CN. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

• Brand: Unbranded
• Working voltage: 12～24V
• Working frequency: 77Ghz~81Ghz
• Horizontal signal angle: ±75°
• Working temperature: -40℃～+85℃
• Power consumption: <2W
• Antenna: dual-transmit and four-receive
• Early warning range: horizontal -5 ~ +5 meters, vertical 0 ~ 50 meters
• Early warning speed range: 0KM/H~120KM/H
• Waterproof rating: lp67
• Distance resolution: 0.4m
• Ranging accuracy: better than 0.18m
• Detection distance: 50m
• Installation method: vertical installation at the rear
• Type: Standard Mirror Assembly

Type:Blind Sport Monitoring System (BSM) Electricity Voltage:12V Maximum Power:5W (max) Working Temperature:-40 degree +85 degree Storage Temperature:-40 degree +85 degree Waterproof level :IP67 Detection Range:Lateral Distance:0.3m – 4m;Rear side Distance: 0.3m-10m. Detection Range Accuracy:>96% Alarm Range:0.3m-10m System Alarm Accuracy:>96% Alarm method:Method 1 LED light turn on. Method 2 LED flash and buzzer sound. Function Introduction: This system is a vehicle assistance device that helps driver lane changing safely during driving. With the aid of 24GHz microwave sensor, probe the side / rear of the vehicle for those moving objects into the blind spot of the detection zone. The system works in a set of a control box (controlled by computer), two microwave sensors, two blind region monitor (or LED light), a buzzer and the wire harness which is the perfect connection of microwave and computer. There is blind zone at the rear of the vehicle which is easy to endanger driving safety! When you installed BSM into your lovely car, no matter it’s day time, night time or even in the snow, you can be alerted whenever there is a moving object pop into the rear of the vehicle, with the aid of LED lighting on , blinking, buzzer sound so that the driver can be cautious when lane changing to avoid the possibility of side crash accident. When you get ready to get off, open the door, if someone moves behind, it will also give an accurate alarm. About installation: Note: 1. Please prepare necessary disassembly tool and protective bumper painted sponge pad or cloth pad. When you disassemble connector, MUST NOT pull wire harness in force, otherwise, will broken the harness. The wire harness should be fixed with the car cable harness by tie band. Neither droop nor abnormal sound. Cut off excess tie band. Disassemble and assemble procedure, please strictly follow our installation manual. Microwave sensor installation cautions points. Microwave sensor (signal launching surface) can only penetrate the plastic bumper case. Microwave sensor (signal launching surface) in the front, must be no metal intervention. Wire connection: Warning: control box is suggested to instll under dash board of driver side (left drive car). Due to wire lenght of LED indicator is limited, when install in a right drive car, please install left/eight LED indicator in vice versa. When green wire connected, system does not work when reverse packing. Connection of this wire is optional. Power supply wire connection (1)Connect black wire of control box with negative side of the vehicle or ground. (2)Connect red wire of control box with vehicle power supply ACC 12V (3) Connect yellow wire of control box with Left turn light 12V. (4) Connect white wire of control box with Right turn light 12V. Connect sensor extension wire with control box, connect sensor A & B with the relativeconnector. Connect left blind spot rear mirror LED light wire with control box relative terminal. Connect right blind spot rear mirror LED light wire with control box relative terminal. Method of Installation 1. Sensor installation (1) Blind sport sensors are to be pasted on vehicle back’s two sides inner arc of plastic bumper, The installation height within 35-90cm. (2) Curve side of microwave sensors install in 10-15 degree to parallel line of car body. Find suitable position of inner side bumper, sticker sensors to it. Avoid insall behind metal, back light or parking sensors, since microwave cannot penetrate these materials, and will affect detection distance. (3) Remove rear plastic bumper, cautious not to scratch the surface paint , put the bumper onto soft sponge or cloth pad. (4) Corresponding side of the remarked outer arc, that is inner arc of the bumper (note: inner arc and outer arc must be at the same position). Wipe the area which sensor is to be pasted by a cloth with alcohol and make a marking. (5) Wipe the sensor surface by a cloth with alcohol, then remove 3M sticker of the back of sensor. Paste 3M sticker on the sensor surface. (Diagram 3) (6) Remove 3M sticker of the sensor, paste sensor on the marked inner arc, press tight, be aware of wire terminal direction of sensor during installation, sensors install horizontally with wire in up or down direction. (Diagram 4) (7) Finally fix the miccowave sensors with 704 silicon glue. Connect sensors wire to control box sensor extension cable. (Diagram 5) (8) Repeat above procedure to install another sensor. Special Blind Sport Mirror Installation (Please skip this procedure for universal product) (1) Remove the front door trim panel and rear view mirror and unplug the heating plug of the mirror. (2) At the front door, pull the LED extension wire to the rear view mirror position, then connect the LED extension wire connector with the relative connector of the BSM rear view mirror of special car. (3) Plug in the heating plug with the BSM rear view mirror. Universal LED light Installation (Please skip this procedure for special product) Please paste LED light on rear view mirror A pillar upside position, it is best to see the position of the rear view mirror at the same time. Control box and buzzer installation Buzzer to attached to the driver’s place. Control box installed in the plastic panel of driver’s main cab dashboard. Should avoid the place of high temperature, moist, leakage. Testing after installation and vehicle parts recovery 1. Confirmation of Installation status (1) Before powering on, check if there is any abnormality in cabling and installation. (2) Specifically check of improperly pressed, stretched, stuck etc. Of the vehicle wire harness. Power Restore (1) Start the car to ensure that the vehicle functions properly. (2) If any abnormalities occur, please check wire harness installation. Functional Test and parts recovery (1) Start the car, move car near the back of sensor to see if LED is light on, both left and right side is to be tested. (2) Switch on both “Left / Right turn on light” separately, when move near car, test if LED blinks and produce sound alert altogether. (3) Functionality test passed, then restore those uninstalled original car parts and check if all function properly. User’s Guide 1. After the car ACC is powered on, the LED lights installed on the left and right sides will light at the same time and turn off after 1 second, indicates that the system is powered up. The system enters the working status immediately. After the system enters the working status, it detects the blind areas (cover both sides of the driveway, length direction is about 10 meters) of the rear sides of the car. When the reverse gear is hung, the system enters interference avoidance mode, the system is temporarily shut down, and the system resumes working mode after exiting the reverse gear. Left/Right side blind area check: (1) When moving vehicle is detected in the left/right rear blind zone, left/right side LED light will light up. (2) If you turn on the Left/right turn signal at this time, then Left/right side LED light flash as the reminder. Simultaneously, buzzer sounds three consecutive alarms. Notice Before the lane changes in the actual lane, be sure to inspect the surrounding area. The system is used only to assist you in detecting the vehicles behind the lane. Due to some restrictions on the actual working environment, sometimes the vehicle is in the adjacent lane, but the system is tied. The unified warning signal lights are not flickered or may delay glint. It is not entirely dependent on this system, and the company is not responsible for any accident. Under the following circumstances, the radar sensor cannot detect the target object. The vehicle is in a blind sport behind the adjacent lane, but the vehicle is not close. Opposite approach vehicle. The adjacent lane of the vehicle is very wide, exceeding the detection range of the radar probe. The vehicle nearly at the same speed along with your driveway at a longer driver time. Vehicles in adjacent lanes try to exceed you. Under the following circumstances, system alert lights and alarms may not be activated or may bedelayed. When the vehicle changes from two lanes to the adjacent lane. When driving on steep slopes. When passing through the vertices of a hill or a mountain trail. When small change in radius (deep turn at the intersection). When there is a difference in altitude between the driving lane and the adjacent lane. If the width of the road is narrow, two-lane vehicles may be detected. This system alarm signal light may turn on, when there are on-road or roadside stationary objects (road guards, concrete wall, tunnel, green area, etc). It is easy to install, but this requires a degree of DIY ability and knowledge. We recommend that all productions are installed by professionals. We will not be responsible for productions that have been damaged during installation by non-professionals, but we still can give you support. Instead of opening the dispute directly and easily. Note: due to logistics’ uncontrollable factor, 704 glue may be not trasported. We may send 3M glue to you. Note:Universal Version Not Include Dedicated Rearview Mirror. The item “Car Blind Spot Mirror Radar Detection System BSD BSA BSM Microwave Sensor Blind” is in sale since Thursday, September 5, 2019. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Radar & Laser Detectors”. The seller is “tnhfaq” and is located in Shenzhen, Guangdong. This item can be shipped worldwide.

• Model Name: BSD001DG
• OSD Language: Indonesia
• Storage Temperature: 40degree +85 degree
• Talk Range: 3m-10m
• Type: Visible
• Model: 001
• Modified Item: No
• Country/Region of Manufacture: China
• Custom Bundle: No
• Warranty: 1year
• Waterproof level: IP67K
• Working Temperature: -40degree +85degree
• MPN: CarBlind001
• Brand: Car Blind China
• Alarm Rangey: 0.3m-10m
• Electricity Voltage: DC12V
• Lifepan: Over50000h
• Material Type: ABS
• Maximum Power: 5W (max)

Musical Instruments & Gear. DVDs & Blu-ray & Movies. Clothing, Shoes & Accessories. Cell Phones & Accessories. Video Games & Consoles. Car Side Mirror Blind Spot Microwave Radar Detection Security System BSD BSA BSM. Type:Blind Sport Monitoring System (BSM) Electricity Voltage:12V Maximum Power:5W (max) Working Temperature:-40 degree +85 degree Storage Temperature:-40 degree +85 degree Waterproof level :IP67 Detection Range:Lateral Distance:0.3m – 4m;Rear side Distance: 0.3m-10m. Detection Range Accuracy:>96% Alarm Range:0.3m-10m System Alarm Accuracy:>96% Alarm method:Method 1 LED light turn on. Method 2 LED flash and buzzer sound. Function Introduction: This system is a vehicle assistance device that helps driver lane changing safely during driving. With the aid of 24GHz microwave sensor, probe the side / rear of the vehicle for those moving objects into the blind spot of the detection zone. The system works in a set of a control box (controlled by computer), two microwave sensors, two blind region monitor (or LED light), a buzzer and the wire harness which is the perfect connection of microwave and computer. There is blind zone at the rear of the vehicle which is easy to endanger driving safety! When you installed BSM into your lovely car, no matter it’s day time, night time or even in the snow, you can be alerted whenever there is a moving object pop into the rear of the vehicle, with the aid of LED lighting on , blinking, buzzer sound so that the driver can be cautious when lane changing to avoid the possibility of side crash accident. When you get ready to get off, open the door, if someone moves behind, it will also give an accurate alarm. About installation: Note: 1. Please prepare necessary disassembly tool and protective bumper painted sponge pad or cloth pad. When you disassemble connector, MUST NOT pull wire harness in force, otherwise, will broken the harness. The wire harness should be fixed with the car cable harness by tie band. Neither droop nor abnormal sound. Cut off excess tie band. Disassemble and assemble procedure, please strictly follow our installation manual. Microwave sensor installation cautions points. Microwave sensor (signal launching surface) can only penetrate the plastic bumper case. Microwave sensor (signal launching surface) in the front, must be no metal intervention. Wire connection: Warning: control box is suggested to instll under dash board of driver side (left drive car). Due to wire lenght of LED indicator is limited, when install in a right drive car, please install left/eight LED indicator in vice versa. When green wire connected, system does not work when reverse packing. Connection of this wire is optional. Power supply wire connection (1)Connect black wire of control box with negative side of the vehicle or ground. (2)Connect red wire of control box with vehicle power supply ACC 12V (3) Connect yellow wire of control box with Left turn light 12V. (4) Connect white wire of control box with Right turn light 12V. Connect sensor extension wire with control box, connect sensor A & B with the relativeconnector. Connect left blind spot rear mirror LED light wire with control box relative terminal. Connect right blind spot rear mirror LED light wire with control box relative terminal. Method of Installation 1. Sensor installation (1) Blind sport sensors are to be pasted on vehicle back’s two sides inner arc of plastic bumper, The installation height within 35-90cm. (2) Curve side of microwave sensors install in 10-15 degree to parallel line of car body. Find suitable position of inner side bumper, sticker sensors to it. Avoid insall behind metal, back light or parking sensors, since microwave cannot penetrate these materials, and will affect detection distance. (3) Remove rear plastic bumper, cautious not to scratch the surface paint , put the bumper onto soft sponge or cloth pad. (4) Corresponding side of the remarked outer arc, that is inner arc of the bumper (note: inner arc and outer arc must be at the same position). Wipe the area which sensor is to be pasted by a cloth with alcohol and make a marking. (5) Wipe the sensor surface by a cloth with alcohol, then remove 3M sticker of the back of sensor. Paste 3M sticker on the sensor surface. (Diagram 3) (6) Remove 3M sticker of the sensor, paste sensor on the marked inner arc, press tight, be aware of wire terminal direction of sensor during installation, sensors install horizontally with wire in up or down direction. (Diagram 4) (7) Finally fix the miccowave sensors with 704 silicon glue. Connect sensors wire to control box sensor extension cable. (Diagram 5) (8) Repeat above procedure to install another sensor. User’s Guide 1. After the car ACC is powered on, the LED lights installed on the left and right sides will light at the same time and turn off after 1 second, indicates that the system is powered up. The system enters the working status immediately. After the system enters the working status, it detects the blind areas (cover both sides of the driveway, length direction is about 10 meters) of the rear sides of the car. When the reverse gear is hung, the system enters interference avoidance mode, the system is temporarily shut down, and the system resumes working mode after exiting the reverse gear. Left/Right side blind area check: (1) When moving vehicle is detected in the left/right rear blind zone, left/right side LED light will light up. (2) If you turn on the Left/right turn signal at this time, then Left/right side LED light flash as the reminder. Simultaneously, buzzer sounds three consecutive alarms. Notice Before the lane changes in the actual lane, be sure to inspect the surrounding area. The system is used only to assist you in detecting the vehicles behind the lane. Due to some restrictions on the actual working environment, sometimes the vehicle is in the adjacent lane, but the system is tied. The unified warning signal lights are not flickered or may delay glint. It is not entirely dependent on this system, and the company is not responsible for any accident. Under the following circumstances, the radar sensor cannot detect the target object. The vehicle is in a blind sport behind the adjacent lane, but the vehicle is not close. Opposite approach vehicle. The adjacent lane of the vehicle is very wide, exceeding the detection range of the radar probe. The vehicle nearly at the same speed along with your driveway at a longer driver time. Vehicles in adjacent lanes try to exceed you. Under the following circumstances, system alert lights and alarms may not be activated or may bedelayed. When the vehicle changes from two lanes to the adjacent lane. When driving on steep slopes. When passing through the vertices of a hill or a mountain trail. When small change in radius (deep turn at the intersection). When there is a difference in altitude between the driving lane and the adjacent lane. If the width of the road is narrow, two-lane vehicles may be detected. This system alarm signal light may turn on, when there are on-road or roadside stationary objects (road guards, concrete wall, tunnel, green area, etc). It is easy to install, but this requires a degree of DIY ability and knowledge. We recommend that all productions are installed by professionals. We will not be responsible for productions that have been damaged during installation by non-professionals, but we still can give you support. Instead of opening the dispute directly and easily. Note: due to logistics’ uncontrollable factor, 704 glue may be not trasported. We may send 3M glue to you. Note:Universal Version Not Include Dedicated Rearview Mirror. International Buyers – Please. Please contact your local custom broker for additional information/requirements. We stand behind our products. We will respond within 24 hours or less. We do our best to process as quickly as possible. We look forward to providing you excellent service! Message us for return instructions. We are unable to accept any items that have been used as well as any food items. These charges are the buyers responsibility. We do not mark merchandise values below value or mark items as gifts – US and International government regulations prohibit such behavior. The item “Car Side Mirror Blind Spot Microwave Radar Detection Security System BSD BSA BSM” is in sale since Saturday, March 28, 2020. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Radar & Laser Detectors”. The seller is “diskhouse” and is located in Shenzhen. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Brazil, Australia.

• Warranty: 1year
• Maximum Power: 5W (max)
• Talk Range: 3M*10M
• Working Temperature: -40degree +85degree
• Material Type: ABS
• Country/Region of Manufacture: China
• OSD Language: English
• Electricity Voltage: DC12V
• MPN: Does Not Apply
• Brand: Unbranded
• Type: Visible
• Model Name: BSD001DG

Car Blind Spot Mirror Radar Detection System BSD BSA BSM Microwave Blind Spot Monitoring Assistant Car Driving Security. Type:Blind Sport Monitoring System (BSM) Electricity Voltage:12V Maximum Power:5W (max) Working Temperature:-40 degree +85 degree Storage Temperature:-40 degree +85 degree Waterproof level :IP67 Detection Range:Lateral Distance:0.3m – 4m;Rear side Distance: 0.3m-10m. Detection Range Accuracy:>96% Alarm Range:0.3m-10m System Alarm Accuracy:>96% Alarm method:Method 1 LED light turn on. Method 2 LED flash and buzzer sound. Function Introduction: This system is a vehicle assistance device that helps driver lane changing safely during driving. With the aid of 24GHz microwave sensor, probe the side / rear of the vehicle for those moving objects into the blind spot of the detection zone. The system works in a set of a control box (controlled by computer), two microwave sensors, two blind region monitor (or LED light), a buzzer and the wire harness which is the perfect connection of microwave and computer. There is blind zone at the rear of the vehicle which is easy to endanger driving safety! When you installed BSM into your lovely car, no matter it’s day time, night time or even in the snow, you can be alerted whenever there is a moving object pop into the rear of the vehicle, with the aid of LED lighting on , blinking, buzzer sound so that the driver can be cautious when lane changing to avoid the possibility of side crash accident. When you get ready to get off, open the door, if someone moves behind, it will also give an accurate alarm. About installation: Note: 1. Please prepare necessary disassembly tool and protective bumper painted sponge pad or cloth pad. When you disassemble connector, MUST NOT pull wire harness in force, otherwise, will broken the harness. The wire harness should be fixed with the car cable harness by tie band. Neither droop nor abnormal sound. Cut off excess tie band. Disassemble and assemble procedure, please strictly follow our installation manual. Microwave sensor installation cautions points. Microwave sensor (signal launching surface) can only penetrate the plastic bumper case. Microwave sensor (signal launching surface) in the front, must be no metal intervention. Wire connection: Warning: control box is suggested to instll under dash board of driver side (left drive car). Due to wire lenght of LED indicator is limited, when install in a right drive car, please install left/eight LED indicator in vice versa. When green wire connected, system does not work when reverse packing. Connection of this wire is optional. Power supply wire connection (1)Connect black wire of control box with negative side of the vehicle or ground. (2)Connect red wire of control box with vehicle power supply ACC 12V (3) Connect yellow wire of control box with Left turn light 12V. (4) Connect white wire of control box with Right turn light 12V. Connect sensor extension wire with control box, connect sensor A & B with the relativeconnector. Connect left blind spot rear mirror LED light wire with control box relative terminal. Connect right blind spot rear mirror LED light wire with control box relative terminal. Method of Installation 1. Sensor installation (1) Blind sport sensors are to be pasted on vehicle back’s two sides inner arc of plastic bumper, The installation height within 35-90cm. (2) Curve side of microwave sensors install in 10-15 degree to parallel line of car body. Find suitable position of inner side bumper, sticker sensors to it. Avoid insall behind metal, back light or parking sensors, since microwave cannot penetrate these materials, and will affect detection distance. (3) Remove rear plastic bumper, cautious not to scratch the surface paint , put the bumper onto soft sponge or cloth pad. (4) Corresponding side of the remarked outer arc, that is inner arc of the bumper (note: inner arc and outer arc must be at the same position). Wipe the area which sensor is to be pasted by a cloth with alcohol and make a marking. (5) Wipe the sensor surface by a cloth with alcohol, then remove 3M sticker of the back of sensor. Paste 3M sticker on the sensor surface. (Diagram 3) (6) Remove 3M sticker of the sensor, paste sensor on the marked inner arc, press tight, be aware of wire terminal direction of sensor during installation, sensors install horizontally with wire in up or down direction. (Diagram 4) (7) Finally fix the miccowave sensors with 704 silicon glue. Connect sensors wire to control box sensor extension cable. (Diagram 5) (8) Repeat above procedure to install another sensor. Special Blind Sport Mirror Installation (Please skip this procedure for universal product) (1) Remove the front door trim panel and rear view mirror and unplug the heating plug of the mirror. (2) At the front door, pull the LED extension wire to the rear view mirror position, then connect the LED extension wire connector with the relative connector of the BSM rear view mirror of special car. (3) Plug in the heating plug with the BSM rear view mirror. Universal LED light Installation (Please skip this procedure for special product) Please paste LED light on rear view mirror A pillar upside position, it is best to see the position of the rear view mirror at the same time. Control box and buzzer installation Buzzer to attached to the driver’s place. Control box installed in the plastic panel of driver’s main cab dashboard. Should avoid the place of high temperature, moist, leakage. Testing after installation and vehicle parts recovery 1. Confirmation of Installation status (1) Before powering on, check if there is any abnormality in cabling and installation. (2) Specifically check of improperly pressed, stretched, stuck etc. Of the vehicle wire harness. Power Restore (1) Start the car to ensure that the vehicle functions properly. (2) If any abnormalities occur, please check wire harness installation. Functional Test and parts recovery (1) Start the car, move car near the back of sensor to see if LED is light on, both left and right side is to be tested. (2) Switch on both “Left / Right turn on light” separately, when move near car, test if LED blinks and produce sound alert altogether. (3) Functionality test passed, then restore those uninstalled original car parts and check if all function properly. User’s Guide 1. After the car ACC is powered on, the LED lights installed on the left and right sides will light at the same time and turn off after 1 second, indicates that the system is powered up. The system enters the working status immediately. After the system enters the working status, it detects the blind areas (cover both sides of the driveway, length direction is about 10 meters) of the rear sides of the car. When the reverse gear is hung, the system enters interference avoidance mode, the system is temporarily shut down, and the system resumes working mode after exiting the reverse gear. Left/Right side blind area check: (1) When moving vehicle is detected in the left/right rear blind zone, left/right side LED light will light up. (2) If you turn on the Left/right turn signal at this time, then Left/right side LED light flash as the reminder. Simultaneously, buzzer sounds three consecutive alarms. Notice Before the lane changes in the actual lane, be sure to inspect the surrounding area. The system is used only to assist you in detecting the vehicles behind the lane. Due to some restrictions on the actual working environment, sometimes the vehicle is in the adjacent lane, but the system is tied. The unified warning signal lights are not flickered or may delay glint. It is not entirely dependent on this system, and the company is not responsible for any accident. Under the following circumstances, the radar sensor cannot detect the target object. The vehicle is in a blind sport behind the adjacent lane, but the vehicle is not close. Opposite approach vehicle. The adjacent lane of the vehicle is very wide, exceeding the detection range of the radar probe. The vehicle nearly at the same speed along with your driveway at a longer driver time. Vehicles in adjacent lanes try to exceed you. Under the following circumstances, system alert lights and alarms may not be activated or may bedelayed. When the vehicle changes from two lanes to the adjacent lane. When driving on steep slopes. When passing through the vertices of a hill or a mountain trail. When small change in radius (deep turn at the intersection). When there is a difference in altitude between the driving lane and the adjacent lane. If the width of the road is narrow, two-lane vehicles may be detected. This system alarm signal light may turn on, when there are on-road or roadside stationary objects (road guards, concrete wall, tunnel, green area, etc). It is easy to install, but this requires a degree of DIY ability and knowledge. We recommend that all productions are installed by professionals. We will not be responsible for productions that have been damaged during installation by non-professionals, but we still can give you support. Instead of opening the dispute directly and easily. Note: due to logistics’ uncontrollable factor, 704 glue may be not trasported. We may send 3M glue to you. Note:Universal Version Not Include Dedicated Rearview Mirror. The item “Car Blind Spot Mirror Radar Detection System BSD BSA BSM Microwave Blind Spot Mo” is in sale since Thursday, October 17, 2019. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Radar & Laser Detectors”. The seller is “mahnt-72″ and is located in Shenzhen. This item can be shipped worldwide.

• Type: Visible
• Warranty: 1year
• Waterproof level: IP67K
• Working Temperature: -40degree +85degree
• Alarm Range: 0.3m-10m
• Model: 001
• Electricity Voltage: DC12V
• Lifepan: Over50000h
• Material Type: ABS
• Maximum Power: 5W (max)
• Model Name: BSD001DG
• OSD Language: Chinese (Traditional), English
• MPN: CarBlind001
• Storage Temperature: -40degree +85 degree
• Talk Range: 3M*10M